Planning a bore
How do you plan a directional bore shot?
Work backward from the crossing: pothole the lines you must clear, set the depth you need under them, then lay out entry and exit points so the rods can dive, run level and climb inside their bend limits. Size the reamer and fluid last, from the pipe you are pulling.
A bore that goes wrong usually went wrong on paper, before the rig was set. The pipe was too big for the hole, the entry was too close to the crossing to reach depth, or nobody knew what was under the road. This is the order to think it through. The numbers come from your rig, your pipe and your spec, and the calculators below do the arithmetic.
1. Know what is already down there
Call 811 first, and do it early enough that the marks are in before you set up. See how far ahead to call. Marks are approximate, so pothole every crossing you can reach to get the real depth, and write it down. The potholing guide covers how. The depth you plan has to clear what you find, with room for the bore to wander.
2. Set the depth you need
Three things set depth: the utilities you must stay under or clear, the cover your spec or permit requires, and the road or crossing itself. Under a road, the agency or railroad that owns it often sets a minimum depth and a method in its permit. Use the permit's number, not a rule of thumb from another job. Plan around the shallowest point of the bore, because that is the one an inspector measures.
3. Lay out entry and exit
The rods cannot turn from vertical to horizontal at once. They dive at a pitch, level off, and climb out, and each of those takes surface distance. So the entry pit has to sit far enough back from the crossing to reach depth, and the exit has to sit far enough past it to climb out again.
Take a 200 foot shot to 6 feet deep with 10 foot rods at 20 percent pitch. Each rod drops 10 x 0.20 = 2 feet, so 3 rods reach 6 feet and cover about 30 feet. The same 3 rods climb out at the far end. That leaves about 140 feet to run level, or 14 rods, for 20 rods in all. Those are the same figures worked in how many rods a bore takes, and the bore calculator runs them for your rod length, pitch and depth. If the lot is too short for the entry run, you either start the bore deeper from a pit or choose a gentler plan; the calculator shows which.
4. Respect the bend limits
Two things bend: the drill rod and the product. The rod can only change pitch so much from one rod to the next, so a steep dive cannot go level in a single rod. The product has its own minimum bend radius, and the pipe or cable maker publishes it. A pull that follows a tighter curve than the product allows can kink pipe or overstress cable. For fiber and cable, the fiber bend radius calculator checks it. Use your rod maker's limit and the product's limit, whichever is tighter.
5. Size the hole for the pull
Once you know the length and the product, size the backream. A common start is 1.5 times the product's outside diameter, going bigger for a long pull or swelling clay. A 4.5 inch pipe at 1.5 times is 6.75 inches. The reamer sizing guide explains the factors and bundles, and the reamer size calculator does the math.
6. Plan the fluid and the spoil
A bigger hole takes more fluid and makes more spoil to vac and haul, and you need somewhere to put it. Run the volume in the drilling fluid calculator before you order or book a vac truck. Plan for a frac-out as well: know where the fluid goes if it surfaces, and have containment on the truck.
7. Write the plan down
A one-page plan beats memory: depths from the potholes, entry and exit locations, rod count, reamer size, fluid volume and the ticket number. Keep it with the job so the crew and the office are on the same page, and so the as-built at the end matches what was planned.
Common questions
How deep should a bore be under a road? The permit or spec sets it. Pothole the utilities nearby, then take the deeper of what they need and what the agency requires.
How far back does the entry pit sit? Far enough for the rods to reach depth at your pitch. Rod length times pitch gives the drop per rod, and the calculator gives the run.
Do I need to ream if the pilot is big enough? Usually yes. The pilot is small, and the product needs a larger hole to pull through.
Who sets the bend limit? Both the rod maker and the product maker. Plan to the tighter one.
For more on how the method works, read what directional drilling is. Boring crews keep the plan, the ticket and the footage on one job in TrackOver for drilling and boring.